Skip to main content

Trunk Finishing Touches

I am not sure why but the last few days working on the car always seem to be the most satisfying.  The trunk only needed a false panel to tie everything together along with some cleanup.  Using some thin plywood, I cut holes to view the insides of the speaker boxes as well as the amps.  I installed some staples to hold the center Plexiglas in place similar to how picture frames are designed.  It ended up working out great!..

Once satisfied with the fit and finish, I covered the assembly with matching carpet and installed the  Plexiglas.


The final task was to wire up the LED's to the trunk latch.  This way they would turn on when the trunk was opened.  Of course if Dan wants them turned off, he can always use the remote to do that!

In the light this is what it looks like.


But I prefer to look at it in the dark!!


I had a lot of fun with this project but as with everything else, eventually it is time to move on to something new.  I really appreciate you following me along this journey and taking the time to read through this blog.  It had its ups and downs but we pushed through and finished.

Until the next project......!!!

Comments

  1. UnknownNovember 28, 2018 at 6:26 PM

    This came out better than I ever expected. I had my own ideas but Tom was the one in possession of my car and ultimately I left the build to him. I couldn't have done better myself and the trunk may be my favorite part of the car besides the B&M shifter and overhead console. Honestly everything Tom did was beyond my expectations.

    ReplyDelete

Post a Comment

Popular posts from this blog

Overhead Console Install

One of the "asks" was to install and wire in an overhead console.  I believe it was from an Astro Van and nothing about it fit the Impala.  I was quite surprised how long the install took but the finished product is really all that matters in the end. I first disassembled the console so I could paint it as well as figure out how to best install the darn thing. With the headliner out, I can form the base to conform to the Impala headliner.  I decided to use thin aluminum sheets and rivet them to the sides to fill the gaps. I then covered the base with material that matched the headliner. Painting everything the same matte black color as the rest of the car so it matches. Lastly the final assembly.  I as really happy with how it turned out thus far. I really hate cutting up a perfectly good headliner but this mod requires it.  Most people cut huge holes and also drill into the cross brace and use screws/hardware that can damage the roof if not careful.  I
Post a Comment
Read more

Center Console

The center console needed to get modified so it would work with the new B&M shifter.  If we had a '96 console, things would have been much easier.  Unfortunately they are very expensive so the '95 console was used.  The two cup holders were situated exactly where the shifter needed to be so out comes the power tools. After the console area was cut, I purchased a piece of ABS plastic and formed it using a heat gun to match the contours.  It then got cut to make room for the modified shifter bezel. The panel was then glued to the console using ABS adhesive.  Because the colors didn't quite match, the console was washed and prepared for some SEM plastic paint. I am really happy with the end result.  Not sure if I'd want to do it again because as simple as it seems, I had 12+ hours into the console.
1 comment
Read more

Speaker Box Build

When we initially went over the terms of the project, I stated that I did not want to do a full custom stereo installation.  As time progressed, I had spent so much time working on it, I didn't want to do a half-ass job finishing the trunk.  We went back and forth on ideas but in the end, I decided to just finish the car so Dan could enjoy it rather than get it back and continue to work on it. The first task was to build the speaker boxes that would house two Infinity Perfect 12 inch subs.  He wanted a good punch but not a booming sound.  After looking over the specs, that meant a sealed box of 1 cubic foot for each sub.  The trunk floor is not flat in a B-body so templates had to be built to accommodate the odd shape.  I decided to built 2 separate boxes - one for each side of the trunk. Here is the outline of the speaker box faces.  I had just barely enough room to mount a 12 inch subwoofer into the panel.  My goal was to be able to mount the amps and crossovers between the b
Post a Comment
Read more