Skip to main content

Where Do We Start?

11/11/17
When starting a project like this, it is often best to sit back and just start with a clean slate.  A better part of yesterday was spent working on the car.  We removed everything inside the cabin and then took out the interior itself.  With the car empty, we vacuumed the floor and removed some of the wires that were in our way.  The car was then pushed into the driveway so it could get it's first bath in probably a decade or more.  There appears to be a lot of oil or other substance on the paint.  While Dan said to not worry about it, I bet it will get cleaned up eventually.

Here are some pictures of the car before we started to do anything..

Rear of the car - as you can see the car is in need of a lot of TLC

Engine bay - the harness has to get pulled and replaced with a new one.  Battery needs replacement and there are tons of little details that need to be resolved.
Interior - new carpet and all trim pieces will get painted black.  This is where most of the time will eventually get spent.

Seats - new rear seat will get installed.  The original one got damaged when some guys broke into it years ago!


"Trunk-o-Parts"... nothing to be seen here!!!

Comments

Post a Comment

Popular posts from this blog

Overhead Console Install

One of the "asks" was to install and wire in an overhead console.  I believe it was from an Astro Van and nothing about it fit the Impala.  I was quite surprised how long the install took but the finished product is really all that matters in the end. I first disassembled the console so I could paint it as well as figure out how to best install the darn thing. With the headliner out, I can form the base to conform to the Impala headliner.  I decided to use thin aluminum sheets and rivet them to the sides to fill the gaps. I then covered the base with material that matched the headliner. Painting everything the same matte black color as the rest of the car so it matches. Lastly the final assembly.  I as really happy with how it turned out thus far. I really hate cutting up a perfectly good headliner but this mod requires it.  Most people cut huge holes and also drill into the cross brace and use screws/hardware that can damage the roof if not careful.  I
Post a Comment
Read more

Center Console

The center console needed to get modified so it would work with the new B&M shifter.  If we had a '96 console, things would have been much easier.  Unfortunately they are very expensive so the '95 console was used.  The two cup holders were situated exactly where the shifter needed to be so out comes the power tools. After the console area was cut, I purchased a piece of ABS plastic and formed it using a heat gun to match the contours.  It then got cut to make room for the modified shifter bezel. The panel was then glued to the console using ABS adhesive.  Because the colors didn't quite match, the console was washed and prepared for some SEM plastic paint. I am really happy with the end result.  Not sure if I'd want to do it again because as simple as it seems, I had 12+ hours into the console.
1 comment
Read more

Speaker Box Build

When we initially went over the terms of the project, I stated that I did not want to do a full custom stereo installation.  As time progressed, I had spent so much time working on it, I didn't want to do a half-ass job finishing the trunk.  We went back and forth on ideas but in the end, I decided to just finish the car so Dan could enjoy it rather than get it back and continue to work on it. The first task was to build the speaker boxes that would house two Infinity Perfect 12 inch subs.  He wanted a good punch but not a booming sound.  After looking over the specs, that meant a sealed box of 1 cubic foot for each sub.  The trunk floor is not flat in a B-body so templates had to be built to accommodate the odd shape.  I decided to built 2 separate boxes - one for each side of the trunk. Here is the outline of the speaker box faces.  I had just barely enough room to mount a 12 inch subwoofer into the panel.  My goal was to be able to mount the amps and crossovers between the b
Post a Comment
Read more